DC-DC|Evaluation
Heat Calculation for Package Selection: Example 2
2019.02.21
Points of this article
・Losses are determined in order to perform heat calculations.
・Heat dissipation measures are taken so as to ensure that Tj does not exceed the absolute maximum rating.
In this article, in succession to the previous “Heat Calculation for Package Selection: Example 1“, we consider, as “Heat Calculation Example 2”, measures to enable use of a desired package.
Heat Calculation for Package Selection: Example 2
We first review the previous loss calculations and calculation results, and then indicate the heat calculation results under those conditions.
Mounting Board, Thermal Resistance, Power Dissipation (PD), Tjmax
Heat Calculation Results for Condition ①
Tj=Ta+θja×P ⇒ 85℃+189.4℃/W×1.008W=275.9℃ → exceeds Tjmax=150℃, FAIL
The above is a summary of the previous article; in actuality, for a Tjmax=150℃, the temperature is a complete FAIL at 275.9℃, rendering further study unnecessary.
In light of this result, here calculations are performed for the other board condition ② described above.
②: 4-layer PCB (2 inner layers copper foil area of PCB, copper foil area on the backside of PCB: 74.2×74.2mm)
Condition②:θja=40.3℃/W
Tj=Ta+θja×P ⇒ 85℃+40.3℃/W×1.008W=125.6℃ → lower than Tjmax=150℃, PASS
Under condition ②, through the heat dissipation effect of a 4-layer board, the thermal resistance was reduced from 189.4°C/W to 40.3°C/W, or nearly 1/5 the original value. Hence even when Ta=85°C, a margin with respect to Tjmax of about 24°C was achieved. This can also be confirmed by the fact that the point of intersection of the 1.008 W line, indicated in red in the above graph of allowable losses, and the line at which Ta=85°C, is inside the allowable loss curve for condition ②.
With this, it is found that the HTSOP-8 package that was chosen can in fact be used, but that as the board, a 4-layer board must be employed.
While these examples are somewhat extreme, experience with such calculations enables one to immediately understand the general conditions that are necessary. However, in order to reach a conclusion, proper calculation of the power losses should not be neglected.
【Download Documents】Basic of Linear Regulators and Switching Regulators
Basic studies for linear regulators and switching regulators as a DC-DC converter.
List of articles related to the「Heat Calculation for Package Selection: Example 2」
- Introduction
- Definitions and Heat Generation
- Losses in Synchronous Rectifying Step-Down Converters
- Conduction Losses in Synchronous Rectifying Step-Down Converters
- Switching Losses in Synchronous Rectifying Step-Down Converters
- Dead Time Losses in Synchronous Rectifying Step-Down Converters
- Controller IC Power Consumption Losses in a Synchronous Rectifying Step-Down Converter
- Gate Charge Losses in a Synchronous Rectifying Step-Down Converter
- Conduction Losses due to the Inductor DCR
- Example of Power Loss Calculation for a Power Supply IC
- Simplified Method of Loss Calculation
- Heat Calculation for Package Selection: Example 1
- Loss Factors
- Matters to Consider When Studying Miniaturization by Raising the Switching Frequency
- Important Matters when Studying High Input Voltage Applications
- Important Matters when Studying Large Output Currents Applications: Part 1
- Important Matters when Studying Large Output Currents Applications: Part 2
- Summary
Download Technical Documents
Basic of Linear Regulators and Switching Regulators
Basic studies for linear regulators and switching regulators as a DC-DC converter.
DC-DC
- Basic
- Design
-
Evaluation
- Overview of Characteristics and Evaluation Method of Switching Regulators
- How to Read Power Supply IC Datasheets: Cover, Block Diagram, Absolute Maximum Ratings and Recommended Operating Conditions
- Evaluating a Switching Regulator: Output Voltage
-
Introduction
- Definitions and Heat Generation
- Losses in Synchronous Rectifying Step-Down Converters
- Conduction Losses in Synchronous Rectifying Step-Down Converters
- Switching Losses in Synchronous Rectifying Step-Down Converters
- Dead Time Losses in Synchronous Rectifying Step-Down Converters
- Controller IC Power Consumption Losses in a Synchronous Rectifying Step-Down Converter
- Gate Charge Losses in a Synchronous Rectifying Step-Down Converter
- Conduction Losses due to the Inductor DCR
- Example of Power Loss Calculation for a Power Supply IC
- Simplified Method of Loss Calculation
- Heat Calculation for Package Selection: Example 1
- Heat Calculation for Package Selection: Example 2
- Loss Factors
- Matters to Consider When Studying Miniaturization by Raising the Switching Frequency
- Important Matters when Studying High Input Voltage Applications
- Important Matters when Studying Large Output Currents Applications: Part 1
- Important Matters when Studying Large Output Currents Applications: Part 2
- Summary
- Application
- Product Information
- FAQ